kb:kb_articles:kb0074

NLM Tech FAQ (Network Compatibility)

1.  Are there any known problems installing the NLM?  Any problems I should watch out for during installation?

The most important thing to remember is to be certain to back up your system before beginning the installation of the Revelation NLM in case you run into a problem. 

 

2.  Can the NLM work on multiple servers?

Yes, the NLM can work across multiple servers, but you must have a separate copy of the NLM for each server.

 

3.  I am installing the NLM on my Advanced Revelation system.  I went to install the client/workstation software and I ran setup and it asked  me whereOpenInsight is.  What am I doing wrong?

If you are installing the NLM client software on a workstation that is running Open Insight for Windows, you need to run the setup.exe program from within Windows.  However, if you are installing the NLM client software on a workstation that is running Advanced Revelation,  the network driver needs to be installed from a DOS prompt  This is done by typing AREV INSTALL /X when you are in the directory where the AREV software is located in on your network.

 

4.  I typed AREV INSTALL /X but I'm not getting an install menu.  What now?

The install menu may have been disabled by the programmer that developed your system.  You can manually run the menu from TCL by typing:

RUNMENU INSTALL

This will run the install menu, you can now proceed with the installation normally.

 

5.  I tried RUNMENU from TCL and it STILL didn't work!

You should contact technical support at 201-594-1422.

 

6.  I tried AREV INSTALL and it asked me for a password, where can I get that?

The developer who wrote your application put a password on the install user to prevent any attempt to gain access to the system via this user.  You should contact the developer of the application for the password.  If you do not know how to contact the developer of your application, you need to contact Revelation Software s Technical Support for assistance.

 

7.  Once I have the network driver installed properly, when  should I load the TSR? 

Pure DOS: You should load the TSR right after you login to your network. 

Win 3.x: You should load the TSR prior to running windows

Win95/NT: You should load the TSR on the batch file line in the shortcut. 

 

 

You can load the TSR from a network drive as long as you place the full path of the location of the TSR in the batch file.  This way, if there is ever an upgrade to the TSR, you only need to upgrade it in one place.

Also if you are using the NLM and Windows95  you must use the /p parameter when you load the TSR, do not use this if you are using pure DOS or windows 3.x and DOS.

Under Windows  95 you also must make sure that background processing is enabled for AREV.  IF you do not have this enabled the NLM will time out.

Right click on the AREV icon

choose properties

choose the miscellaneous tab

and make sure  always suspend  is NOT be checked off

 

8.  How can I confirm that the TSR is loaded?

Please refer to the NLM installation documentation (page 17) for a detailed description of how to test if a workstation is running the TSR.  There is a function you can run that you can add to the login script so you can limit access to the NLM to only those AREV users that have the TSR loaded, thus avoiding a situation which would result in data corruption

 

9.  If I am running OpenInsight, do I need to load the TSR? 

No you do not.  You only need to load the TSR for AREV applications.

 

10.  What is local mode, and what is the REVPARAM file used for?

Local mode refers to how the data files are accessed.  When we say that you are accessing the linear hash data files in local mode it means that the workstation is directly accessing the data.  The NLM is designed so that the server accesses the data files, you designate this with the REVPARAM file which is located in every directory where there are linear hash files by placing this file in any directory with the line: ServerOnly=True in it will only allow the server to access the data.

 

11.  I tried to install the NLM on my Novell server and I am getting "Insufficient disk space" errors but the drive has plenty of drive space, what s wrong here?

You might want to verify that the files have valid owners. Under Novell if files do not have owners you can get disk full errors. If you go to the directory where you keep these files and type NDIR it will show you who the owners are. If you see N/A it means that the file has no owner and it needs to be assigned. The FILER utility is how you can assign ownership of the files.  This type of error can happen if you delete a user without reassigning ownership of the files that the user had.

Another potential issue to look for under Novell while installing the NLM is to make certain that the Novell attributes are allowing you to modify theOpenInsight/AREV files.  You can use the flag command from a command prompt to see what the attributes are.  If these are read only, you need to change the file attributes to read/write.  You also may not have the DI or RI flags set.  These attributes can be set with the Novell FLAG command.

 

12.  I just upgraded the NLM and now I'm getting a Linear version synch error, what's wrong?

This error only occurs when one of the NLM modules is the wrong version.  You need to verify that the TSR, NLM and AREV network driver are all the correct version.  To check the TSR all you need to do is type lhipxtsr /? when you are in the directory that the TSR resides in.  To get the NLM version you need access to type MODULES at either the server itself or via RCONSOLE.  The NLM is listed under LH.NLM.  Finally you can check the AREV driver by typing WHO inTCL  Under Optional Module Information it will list the IPX -NETWORK-Driver and its version.  The current versions of these programs are:

LH.NLM: 1.10

LHIPXTSR: 1.12

IPX-NETWORK-DRIVER: 1.12

 

13.  How can you tell if the NLM on the server is actually up and running properly?

A workstation can verify that the NLM is handling the transactions by checking the file handle for a file located on a server running the revelation NLM.  The file handle should contain six  F  values. 

To view the file, go to the TCL prompt and type the following:

EDIT SYSTABLES VOC    

You should see the following information:

NLM File handle:  0000008FFFFFFREV12345.LK

 

14. I just installed the NLM and have noticed a decrease in performance.  I thought I was supposed to see an increase in performance?  Any suggestions?

Yes, more than likely you just need to do a little fine tuning to your system.  Make sure that you are using as few protocols as possible on your system.  The more protocols you have running, the slower your system will be.  Also, if you are running your AREV or OI application from a Win  95 machine or a Windows NT machine, make sure you are using Novell s Client 32 driver instead of the Microsoft IPX/SPX driver.  A good rule of thumb is as follows:  When connecting to a Novell server, it is always best to use Novell s drivers.  When connecting to an NT server, it is always best to use Microsoft drivers. 

  • kb/kb_articles/kb0074.txt
  • Last modified: 2024/01/30 13:36
  • by 127.0.0.1